· by Michael Blair, Nashville's Appliance Repair
A dryer that tumbles and blows air but never gets warm sometimes needs dryer repair and sometimes needs nothing more than a reset. The manufacturers’ own help pages agree on a short list to rule out first, most of it outside the machine: the cycle setting, the breakers, the supply voltage and, on a gas dryer, the gas valve. Here is that list in the order worth checking, what each one means, and where the job becomes ours.
Is the dryer set to a cycle that heats?
A dryer set to an air-only cycle will tumble without heat every time, so the setting is the first thing to check. Whirlpool’s help page for an electric dryer that is not heating says the Air Only or Air/Fluff cycle adds no heat at any point in the cycle, and Frigidaire lists the air fluff and temperature selections among its first checks too.
To find out whether there is any heat at all, Whirlpool suggests a quick test: choose a heated timed cycle, run the dryer empty for five minutes, then open the door and feel inside. Warm air means the dryer is heating and the problem is more likely slow drying than no heat, which has its own causes. Cold air on a heated cycle means it is time to look at the power or the gas.
Why can an electric dryer spin while one breaker is off?
An electric dryer can spin with one breaker off because it is wired on two circuits, one that runs the motor and one that runs the heating element. Whirlpool and Maytag both call for its own 30-amp circuit with a fuse or breaker on each leg of the power, so two breakers, and say that if one of them trips the dryer may not heat. Frigidaire’s page, My dryer is running, but does not seem to be heating, says the same of a blown fuse: the drum turns, the heater does not.
Samsung’s guide for clothes that are not dry adds that the two circuits are usually tied to trip together, but only one can trip. Its fix is to switch the breaker fully off, wait 30 seconds and switch it back on. Samsung also notes that an outlet not supplying enough voltage can leave the panel and motor working while the heater does not. Electric dryers need a 240-volt supply, and checking that is for a qualified electrician, as Whirlpool and Frigidaire both say.
What stops a gas dryer from heating?
A gas dryer stops heating, while its drum keeps turning, when gas is not getting to the burner. Maytag’s page on a dryer that is not heating says a closed shutoff valve does exactly that, and that the valve is open when its handle runs parallel to the gas pipe. Frigidaire adds an empty propane tank to the list for dryers on LP, and points out that a gas dryer needs space around it for ventilation to support the burner, so a machine pushed hard into a tight closet is worth a second look.
If you smell gas at any point, stop checking the dryer, leave it off, and call your gas company from somewhere away from the house. A gas dryer that has the valve open, fuel available and room around it, and still blows cold, needs its ignition and gas parts tested, and that is a job for us rather than a weekend project.
When does a no-heat dryer need a technician?
A no-heat dryer needs a technician once the cycle, both breakers, the supply voltage and, on gas, the valve all check out and the drum still turns cold. At that point the problem is inside the machine, and we test the heating parts and the safety devices that cut the heat, with the dryer unplugged. Whirlpool’s own instructions say to unplug the dryer before checking anything at the power terminals, and the heating side of an electric dryer runs on 240 volts, so this is not the place to experiment.
One more distinction saves a lot of guessing. Maytag says that a dryer which heats but still takes a long time to dry most likely has a vent problem or restricted airflow, and that the venting should be cleaned out once every year or two, sooner if it needs it; some Samsung models will even flag a clog on the display. That is a different fault from no heat, and our post on a dryer that takes two cycles covers it. If yours is in Nashville or nearby and has passed every check above, book a dryer visit and tell us whether it is gas or electric.
Sources
- Whirlpool Product Help, Not Heating: Electric Dryer — Five-minute heated timed cycle test; Air Only and Air/Fluff add no heat; dedicated 30-amp circuit with two breakers, one for the motor and one for the element; 240-volt supply, check with an electrician; unplug before checking terminals
- Maytag Product Help, Dryer Is Not Heating — Two breakers and 240 volts; a closed gas valve leaves the drum turning without heat, open when the handle is parallel to the pipe; heating but long dry times points to the vent, cleaned every one to two years
- Frigidaire Owner Support, My dryer is running, but does not seem to be heating — Two house circuits or fuses, drum turns without heat if one trips; air fluff and temperature selection; electrician to verify 240 volts; gas valve and empty LP tank; space around a gas dryer for the burner
- Samsung US Support, Clothes are not dry after using Samsung dryer — Two circuits usually trip together but one can trip alone; breaker off 30 seconds and back on; low voltage can leave panel and motor working without heat; clog detection on some models
FAQ
Dryer Tumbles but Won’t Heat: What to Check First — questions
How do I fix a dryer that has no heat?
Check the cycle first, because air-only and air fluff settings never heat. On an electric dryer, reset both breakers by switching them fully off for 30 seconds and back on, and have an electrician confirm 240 volts. On gas, check that the valve handle runs parallel to the pipe. If those are fine, the heating parts need testing.
Can a tripped breaker make a dryer stop heating?
Yes. Electric dryers run on two circuits, one for the motor and one for the heating element, and Samsung, Whirlpool and Maytag all say that if only one trips, the drum can keep turning while the dryer stays cold. Samsung’s suggested reset is to switch the breaker fully off, wait 30 seconds and switch it back on.
Does an electric dryer need 240 volts?
Yes. Whirlpool, Frigidaire and Samsung all say electric dryers need a 240-volt supply, on a dedicated 30-amp circuit with two breakers. Samsung notes that an outlet supplying too little voltage can leave the controls and motor working while the heater does not. Testing the outlet’s voltage is a job for a qualified electrician.
Does air fluff cycle produce heat?
No. Whirlpool’s help page says the Air Only and Air/Fluff cycles add no heat at any point, so a dryer left on that setting will tumble with cold air every time. Switch to a heated timed cycle, run it empty for five minutes, and feel inside to see whether the dryer is actually heating.
Why is my gas dryer not heating?
Start with the gas shutoff valve; Maytag says the drum will turn without heat if it is closed, and that the valve is open with its handle parallel to the pipe. On propane, check the tank. A gas dryer also needs room around it to ventilate the burner. If you smell gas, stop and call the gas company.